Design of Strap footings
Click the toolbar icon or from the main menu (Foundation -> Strap footing) or type the command strap
Global variables
Please note: this is not an ultimate stress design but it's the traditional working stress method.
Maximum (Shear, bond,punching, tension) strength. | Max. (Shear, bond,punching, tension) strength. | |
Minimum number of steel bars per linear meter | Min. Number of bars/m | |
Thickness of concrete cover in CM | Concrete cover [CM] | |
Bending moment reduction factor , set to 1 for no reduction to take effect. | Bending moment reduction factor. | |
Load enlargement factor factor , set to 1 for no enlargement to take effect. | Factor multiplied by total applied load. |
General data
Soil bearing capacity | Bearing capacity. | |
Steel Working stress. | Steel Working stress. | |
Concrete Working stress. | Conc. Working stress. | |
Thickness of blinding base | Plain concrete depth. | |
Consider plain concrete footing in design calculation | Activate plain concrete base in design. | |
Rebar shape | Bar shape. |
List of input and output
Footing number , If you entered an existing footing number, it will not be added but the existing data will be replaced with the new data | F | ||
C.L to C.L column spacing | L | ||
Left Column: | |||
Total axial load (Tons) | P1 | ||
Column cross section dimension in longitudinal direction (CM) | a1 | ||
Column cross section dimension in short direction (CM) | b1 | ||
Distance from column outer face to the edge of the footing | x1 | ||
Right Column: | |||
Total axial load (Tons) | P2 | ||
Column cross section dimension in longitudinal direction (CM) | a2 | ||
Column cross section dimension in short direction (CM) | b2 | ||
Distance from column outer face to the edge of the footing | x2 | ||
Calculated stress generated by the footing. | Fn | ||
Calculated plain concrete footing dimensions | PC dim. | ||
Calculated reinforced concrete footing dimensions | RC dim. | ||
Calculated Longitudinal direction rebar. (top) | Long top bars | ||
Calculated Longitudinal direction rebar. (bottom) | Long bot. bars | ||
Calculated additional rebar underneath left column | Under L. col. | ||
Calculated additional rebar underneath right column | Under R. col. | ||
Short direction rebar | Short top bars | ||
To remove a footing from the list |
Footing number , If you entered an existing footing number, it will not be added but the existing data will be replaced with the new data ة. | F | |
C.L to C.L column spacing. | L | |
Left Column: | ||
Total axial load (Tons) | P1 | |
Dimensions of plain concrete footing | F1-PC | |
Dimensions of reinforced concrete footing | F1-RC | |
Reinforcement bars on x-axis direction | X-dir. reinf. | |
Reinforcement bars on y-axis direction | Y-dir. reinf. | |
Right Column: | ||
Total axial load (Tons) | P2 | |
Dimensions of plain concrete footing | F2-PC | |
Dimensions of reinforced concrete footing | F2-RC | |
Reinforcement bars on x-axis direction | X-dir. reinf. | |
Reinforcement bars on y-axis direction | Y-dir. reinf. | |
Dimensions of beam cross section | Strap beam | |
Beam bottom reinforcement bars | bot. reinf. | |
Beam top reinforcement barsة | top reinf. | |
Stirrups bar Diameter | Stirrups |
Customizing drawing area
Click to start drawing area configuration.
Colors | Line thicknesses | Elements Scale | Show/Hide | ||||||||||||||||||||||||||||||||
|
|
|
|
To Select colors from the standard dialog box:
To select title and text fonts:
To get the list shown below, on the drawing area rick click the mouse, you can also use the mouse wheel for zooming in and out.
Creating design reports
Once the design work is complete, select views from the list below followed by clicking where screen shots of the drawing area will be taken and included to the report.
The sort sequence of the footings design in the report is matching the sort sequence of the footings in the list, you can sort the list ascending/descending by clicking the list column of title F .
Interface buttons
Steps of work
Setup global variables | 1 | |
Enter the general data | 2 | |
Enter the individual data of each footing | 3 | |
Hit Design button | 4 | |
Setup the drawing area (optional) | 5 | |
Take screen shots of the drawing area , those images will be added to the report | 6 | |
Generate a report | 7 |
تصميم قواعد الجار بكمرات رابطة.
يقوم هذا التطبيق بعملية التصميم لقاعدة على حد الجار مربوطة بقاعدة وسطية .
يمكنك تشغيل التطبيق من شريط الادوات الايكون او من قائمة Foundation اختر Strap footing او على سطر الاوامر اكتب الامر strap
اعداد المتغيرات العامة
لضبط هذه القيم يجب الرجوع الى المواصفات لتحديد القيم المسموح بها. | Max. (Shear, bond,punching, | |
اقل عدد من قضبان التسليح لكل متر . | Min. Number of bars/m | |
غطاء الخرسانة بالسم ، يجب الرجوع الى المواصفات لتحديد القيم المسموح بها.. | Concrete cover [CM] | |
معامل لتخفيض قيم العزوم ، يمكن استخدام القيمة الافتراضية (1) لمنع أي تخفيض وكذلك يجب الرجوع الى المواصفات لتحديد القيم المسموح بها. . | Bending moment reduction factor. | |
معامل لتكبير قيمة الحمل لتغطية أي أحمال أخرى لم تؤخذ في الاعتبار ، يمكن استخدام القيمة الافتراضية (1) للاحتفاظ بقيمة الحمل الأصلية وكذلك يجب الرجوع الى المواصفات لتحديد القيم المسموح بها. .. | Factor multiplied by total applied load. |
المدخلات العامة للقواعد
جهد تحمل التربة بالكجم لكل سم 2. | Bearing capacity. | |
إجهاد التشغيل للحديد بالكجم لكل سم 2 ، يمكن اختيار قيمة من القائمة أو كتابتها مباشرة . | Steel Working stress. | |
إجهاد التشغيل للخرسانة بالكجم لكل سم 2 ، يمكن اختيار قيمة من القائمة أو كتابتها مباشرة .. | Conc. Working stress. | |
عمق قاعدة الخرسانة العادية. | Plain concrete depth. | |
اعتبار او عدم اعتبار قاعدة الخرسانة العادية في التصميم. | Activate plain concrete base in | |
شكل حديد التسليح المستخدم . | Bar shape. |
جدول المدخلات والمخرجات.
رقم القاعدة ، عند إدخال رقم قاعدة موجود بالفعل بالقائمة سيتم تعديل بيانات القاعدة بدلا من إضافة قاعدة جديدة. | F | |
إالمسافة بين العمودين بالسم. | L | |
حمل عمود الجار بالطن. | P1 | |
حمل العمود الداخلي بالطن. | P2 | |
ابعاد قاعدة الجار العادية. | F1-PC | |
ابعاد قاعدة الجار المسلحة. | F1-RC | |
التسليح في اتجاه محور X | X-dir. reinf. | |
التسليح في اتجاه محورY | Y-dir. reinf. | |
ابعاد القاعدة الداخلية العادية | F2-PC | |
ابعاد القاعدة الداخلية المسلحة | F2-RC | |
التسليح في اتجاه محور X | X-dir. reinf. | |
التسليح في اتجاه محور Y | Y-dir. reinf. | |
ابعاد الكمرة الرابطة | Strap beam | |
التسليح السفلي للكمرة | bot. reinf. | |
التسليح العلوي للكمرة | top reinf. | |
الكانات | Stirrups | |
لإلغاء بيانات قاعدة بعد اختيارها من القائمة وضغط زر الماوس الايمن. |
ضبط لوحة الرسم لتطبيق القواعد المنفصلة.
يمكنك الضغط على زر للدخول إلى نافذة إعداد لوحة الرسم.
لون خلفية لوحة الرسم. | Background colour | |
لون خطوط الشبكة. | Grid colour | |
لون النص. | Text colour | |
لون أسياخ التسليح. | Steel bars colour | |
لون رقبة العمود. | Column neck colour | |
لون القاعدة المسلحة. | RC footing colour | |
لون القاعدة العادية. | PC footing colour | |
لون خط البعد. | Dimension line colour | |
لون منحنى العزوم وقوى القص | Bending moment curve colour | |
لون تهشير منحنى العزوم وقوى القص | BM hatch colour | |
لون خط القاعدة | Footing C.L. colour | |
هوامش الرسم. | Drawing margin | |
مقاس قطر أسياخ الحديد لإعطائها إظهار معين. | Bar size | |
سمك خط حديد التسليح. | Steel bars line thickness. | |
سمك خط رقبة العمود. | Column neck line thickness. | |
سمك خط القاعدة المسلحة. | RC base line thickness. | |
سمك خط القاعدة العادية. | PC base line thickness. | |
سمك خط الأبعاد. | Dimension line thickness. | |
سمك منحنى العزوم او قوى القص | BMD line thk. | |
سمك خط القاعدة | Footing line thk. | |
سمك خط التهشير | Hatch line thk. | |
ارتفاع سهم التأثير على عنصر معين. | Leader height. | |
الإزاحة الأفقية للنص عن خط البعد. | Text horizontal shift. | |
الإزاحة الراسية للنص عن خط البعد. | Text vertical shift. | |
مقاس نهاية خط البعد. | Tick length | |
اختيار شكل السهم للأبعاد. | Arrow head | |
إظهار أو إخفاء خطوط الشبكة. | Show grid | |
إظهار أو إخفاء خطوط الأبعاد. | Show dimensions | |
إظهار أو إخفاء النص. | Show text | |
إظهار أو إخفاء حديد التسليح. | Show Reinforcement | |
لاختيار وضبط الفونت المستخدم في النصوص والأبعاد. | ||
لاختيار وضبط الفونت المستخدم في االعناوين. | ||
استعادة الاعدادات الافتراضية. |
بعد إجراء التعديلات واختيار الألوان
قد تظهر شاشة الرسم بالشكل التالي:
يمكنك تعديل الفونت لتحسين لوحة الرسم ويظهر ديالوج اختيار الفونت كما يلي:
بضغط زر الماوس الايمن على لوحة الرسم يتم عرض القائمة التالية حيث يمكن تكبير وتصغير وازاحه الرسم كما يمكنك ضغط زر الماوس الايمن فوق لوحة الرسم لعرض نفس القائمة ويمكن ايضا استخدام عجلة الماوس للتصغير والتكبير
إنشاء التقارير وطباعتها.
بعد إتمام عملية التصميم يمكنك اختيار القواعد المطلوب ضم صور لها إلى التقرير واختيار الشكل المطلوب إظهاره من القائمة التالية:
ثم الضغط على زر لضم الصور إلى التقرير .
بعد الانتهاء من هذه العملية يمكنك الضغط على الزر الخاص بإعداد التقرير
قد يظهر التقرير بالشكل التالي:
يجب الانتباه إلى أن ترتيب تصميم القواعد بالتقرير سيكون حسب ظهور وترتيب القواعد بالقائمة وعليه يمكنك ترتيب القواعد بالقائمة راسيا وتنازليا بالضغط بالماوس على الرمز F والذي يرمز إلى رقم القاعدة وسيتم الترتيب.
طريقة العمل على تطبيق تصميم قواعد الجار والكمرات الرابطة.
قم بإعداد المتغيرات العامة للتصميم | 1 | |
قم بإدخال البيانات العامة لكل القواعد. | 2 | |
قم بإدخال البيانات الخاصة بكل قاعدة . | 3 | |
اضغط زر التصميم. | 4 | |
قم بإعداد لوحة الرسم إذا رغبت . | 5 | |
اختر الصور الخاصة التي ترغب في إضافتها للتصميم. | 6 | |
اضغط زر إعداد التقرير لمراجعته وطباعته. | 7 |